Heat pumps
ECOs HEAT SPLIT with integrated storage tank
HEAT PUMPS
HEAT PUMP
ECOS HEAT SPLIT
with integrated storage tank
In the SEVRA ECOs HEAT Split heat pump, two separate units: the indoor and outdoor units are connected to each other by a refrigerant system. Key components such as the heat exchanger, expansion vessel and water pump are located in the indoor unit. In addition, the risk of water freezing is minimised by locating all water pipes responsible for heating inside the building.
FEATURES OF THE DEVICE
FEATURES OF THE DEVICE
refrigerant
up to -25°C
hot water
up to 60°C
operation
control
compressor
water pump
WiFi module
and weekly schedule
function
disinfection
function
mode
electrical grid
updates
R32 REFRIGERANT
Refrigerant R32
ECOLOGICAL
The refrigerant R32 has a very low GWP of 675. Compared to R410A, which has a GWP of 2088, R32 has a relatively low environmental impact – its global warming impact is up to three times lower. In addition, unlike R410A, R32 is a homogeneous (single-component) refrigerant and can therefore be recycled. All SEVRA heat pumps operate with the latest environmentally friendly refrigerant R32, which, compared to the commonly used refrigerant R410A to date, has greater efficiency and a lower greenhouse effect coefficient. It also does not damage the ozone layer.
HIGH EFFICIENCY
Due to its thermodynamic properties, R32 refrigerant is more efficient than R410A. The installation requires less refrigerant. In addition, R32 increases the energy efficiency of the unit by up to 10%
SAFE
The R32 refrigerant is characterised by low toxicity, thus guaranteeing a high degree of operational safety.
EFFICIENCY
EXCELLENT PERFORMANCE
- On/off unit.
- High heating capacity at low temperatures.
- Wide operating range.
- Two heating circuits.
CONVENIENCE
CONVENIENCE OF USE
- Controller with intuitive interface
- Proprietary Wi-Fi control solution.
- Reduced noise levels.
- Holiday mode.
EASY INSTALLATION
EASY INSTALLATION
AND MAINTENANCE
- Easy commissioning with a wired controller.
- Greater safety of use at lower outside temperatures.
FUNDING
APPLY
FOR THE GRANT
Receive a grant under the Clean Air Programme
The Clean Air Programme – a nationwide programme of financial support for the replacement of heat sources. A programme for owners and co-owners of single-family houses offering subsidies for heat source replacement and thermal modernisation works. The aim of the programme is to improve air quality and reduce greenhouse gas emissions by replacing heat sources and improving the energy efficiency of single-family dwellings
GRANT
FOR WHOM?
A programme aimed at owners or co-owners of single-family residential buildings, or separate residential units in single-family buildings with a separate land register.
SCOPE OF SUPPORT
Subsidising the replacement of old and inefficient solid fuel heat sources with modern heat sources meeting the highest standards, and carrying out the necessary thermal modernisation work on the building.
GRANT AMOUNT
The grant can be up to £30,000 for the basic level of funding and £37,000 for the increased level of funding.
APPLICATION
Applications for funding can be made online or at the office. More information is available at: www.gov.pl
SPECIFICATIONS
TECHNICAL DATA
| Indoor unit | SEV-MHPT-3-10-190/I | SEV-MHPT-3-10-240/I | SEV-MHPT-3-16-240/I | ||||
|---|---|---|---|---|---|---|---|
| Compatibility with units | SEV-HPS1-04/O | SEV-HPS1-06/O | SEV-HPS1-04/O | SEV-HPS1-06/O | SEV-HPS3-12/O | ||
| SEV-HPS1-08/O | SEV-HPS1-10/O | SEV-HPS1-08/O | SEV-HPS1-10/O | SEV-HPS3-14/O | |||
| SEV-HPS3-16/O | |||||||
| Water distribution profile | – | L | XL | XL | |||
| Domestic hot water (temperate climate)* |
Energy class | A+ | A+ | A+ | A+ | A+ | |
| COP | 3,10 | 3,10 | 3.36 | 3.36 | 3,00 | ||
| DHW tank | Type | – | Stainless steel | Stainless steel | Stainless steel | ||
| Material | – | SUS316L | SUS316L | SUS316L | |||
| Water volume | L | 190 | 240 | 240 | |||
| Max. water temp. | st. C | 70 | 70 | 70 | |||
| Insulation | Material | Polyurethane | Polyurethane | Polyurethane | |||
| Thickness (mm) | 45 | 45 | 45 | ||||
| Power supply | V/~/Hz | 220-240/1/50 | 380-415/3/50 | 380-415/3/50 | |||
| Maximum overcurrent protection | A | 14,3 | 14,0 | 14,0 | |||
| Sound power level | dB(A) | 38 | 40 | 43 | |||
| Acoustic pressure level | dB(A) | 28 | 30 | 32 | |||
| Device dimensions (LxWxD) | mm | 600 x 1683 x 600 | 600 x 1943 x 600 | 600 x 1943 x 600 | |||
| Unit weight | kg | 140 | 157 | 159 | |||
| Electric heater | Capacity | kW | 3 | 9 | 9 | ||
| Degrees | – | 1 | 3 | 3 | |||
| Supply water temperature range | Cooling | st. C | 5-25 | 5-25 | 5-25 | ||
| Heating | st. C | 25-65 | 25-65 | 25-65 | |||
| CWU | st. C | 30-60 | 30-60 | 30-60 | |||
| Water connection | R1″ | R1″ | R1″ | ||||
| Cooling connection | 1/4″ – 5/8″ | 3/8″ – 5/8″ | 3/8″ – 5/8″ | ||||
| Water-side exchanger | Type | Plate | Shallow | Plate | |||
| Water pump | Type | – | DC Inverter | DC Inverter | DC Inverter | ||
| Lifting height | m | 9 | 9 | 9 | |||
| Expansion vessel | Capacity | l | 8 | 8 | 8 | ||
| Safety valve | Mpa | 0,3 | 0,3 | 0,3 | |||
(1) Outdoor temperature 7°C DB, 85% R.H.; EWT 30°C, LWT 35°C.
(2) Outdoor temperature 7°C DB, 85% R.H.; EWT 40°C, LWT 45°C.
(3) Outdoor temperature 7°C DB, 85% R.H.; EWT 47°C, LWT 55°C.
(4) Outdoor temperature 35°C DB, EWT 23°C, LWT 18°C.
(5) Outdoor temperature 35°C DB, EWT 12°C, LWT 7°C.
(6) Seasonal energy efficiency class measured under average climatic conditions
Relevant EU standards and regulations: EN14511; EN14825; EN50564; EN12102
The air-conditioning units contain the fluorinated greenhouse gas R32.
Specifications, design and functions of the units are subject to change without prior notice.
The photos of the units are for illustration purposes only, actual appearance may vary.